電動卷簾門的限位調整是確保其正常運行的重要步驟。以下是調整電動卷簾門限位的詳細步驟：

　　The limit adjustment of electric rolling shutter doors is an important step to ensure their normal operation. The following are the detailed steps for adjusting the threshold of the electric roller shutter:

　　一、準備工具和材料

　　1、 Prepare tools and materials

　　螺絲刀（包括菲利普螺絲刀、平面螺絲刀等）

　　Screwdrivers (including Phillips screwdrivers, flat screwdrivers, etc.)

　　扳手

　　Wrench

　　電工膠帶（可選，用于電線連接處的絕緣處理）

　　Electrical tape (optional, used for insulation treatment at wire connections)

　　絕緣手套（確保，防止觸電）

　　Insulated gloves (to ensure safety and prevent electric shock)

　　二、調整上限位

　　2、 Adjust the upper limit

　　斷電準備：

　　Power outage preparation:

　　在進行任何調節前，確保電動卷簾門已斷電，以避免在操作過程中發生電擊或意外閉合。

　　Before making any adjustments, ensure that the electric rolling shutter door is powered off to avoid electric shock or accidental closure during operation.

　　定位上限位開關：

　　Positioning upper limit switch:

　　通常位于電機旁邊，與電機相連，用于控制卷簾門上升到點。

　　Usually located next to the motor and connected to it, it is used to control the rolling shutter door to rise to the highest point.

　　手動調節門簾位置：

　　Manually adjust the position of the door curtain:

　　手動將卷簾門拉希望它完全打開的位置。

　　Manually pull the rolling shutter door to the desired fully open position.

　　調整上限位開關：

　　Adjust the upper limit switch:

　　使用螺絲刀調整上限位的調節螺釘。順時針調節通常會提高上限位，逆時針調節會降低上限位。

　　Use a screwdriver to adjust the upper limit adjustment screw. Clockwise adjustment usually increases the upper limit, while counterclockwise adjustment decreases the upper limit.

　　調整過程中，可輕輕按壓上限位開關，觀察卷簾門是否能夠順利停止上升，并保持在設定的高度。

　　During the adjustment process, gently press the upper limit switch to observe whether the rolling shutter door can stop rising smoothly and maintain the set height.

　　測試與調整：

　　Testing and adjustment:

　　完成調節后，重新通電，測試卷簾門的開啟狀態，觀察門簾是否可以順暢升起并停在設定位置。

　　After completing the adjustment, power on again, test the opening status of the rolling shutter door, and observe whether the door curtain can rise smoothly and stop at the set position.

　　如有需要，可再次調整上限位開關的位置，直到達到預期效果。

　　If necessary, adjust the position of the upper limit switch again until the desired effect is achieved.

　　三、調整下限位

　　3、 Adjust the lower limit

　　斷電準備（同上限位調整步驟1）。

　　Power off preparation (same as upper limit adjustment step 1).

　　定位下限位開關：

　　Position the lower limit switch:

　　通常位于電機旁邊或軌道的另一端，用于控制卷簾門下降到點。

　　Usually located next to the motor or at the other end of the track, it is used to control the rolling shutter door to descend to the lowest point.

　　手動調節門簾位置：

　　Manually adjust the position of the door curtain:

　　手動將卷簾門降希望它完全關閉的位置。

　　Manually lower the rolling shutter door to the desired fully closed position.

　　調整下限位開關：

　　Adjust the lower limit switch:

　　使用螺絲刀調整下限位的調節螺釘。順時針旋轉通常會增加下限位，而逆時針旋轉則會降低下限位。

　　Use a screwdriver to adjust the lower limit adjustment screw. Clockwise rotation usually increases the lower limit, while counterclockwise rotation decreases the lower limit.

　　調整過程中，可輕輕按壓下限位開關，觀察卷簾門是否能夠順利停止下降，并保持在設定的高度。

　　During the adjustment process, gently press the lower limit switch to observe whether the rolling shutter door can smoothly stop descending and maintain the set height.

　　測試與調整（同上限位調整步驟5）。

　　Testing and adjustment (same as upper limit adjustment step 5).

　　四、注意事項

　　4、 Precautions

　　：在調整過程中，務必確保電源已完全切斷，并佩戴絕緣手套以防觸電。

　　Safety first: During the adjustment process, make sure that the power supply is completely cut off and wear insulated gloves to prevent electric shock.

　　細致觀察：在調整限位開關時，要細致觀察卷簾門的運動狀態，確保其在設定位置能夠準確停止。

　　Careful observation: When adjusting the limit switch, carefully observe the movement status of the rolling shutter door to ensure that it can accurately stop at the set position.

　　反復測試：每次調整后都要進行反復測試，確保卷簾門的運行平穩且符合預期。

　　Repeated testing: After each adjustment, it is necessary to conduct repeated testing to ensure that the operation of the rolling shutter door is smooth and meets expectations.

　　維護記錄：建議記錄每次調整的日期、調整前后的限位位置以及測試結果等信息，以便日后維護和排查故障。

　　Maintenance records: It is recommended to record the date of each adjustment, the limit position before and after the adjustment, and the test results for future maintenance and troubleshooting.

　　通過以上步驟，您可以成功調整電動卷簾門的限位開關，確保其正常運行并滿足使用需求。

　　By following the above steps, you can successfully adjust the limit switch of the electric rolling shutter door to ensure its normal operation and meet the usage requirements.

　　本文由 濟南卷簾門 友情奉獻.更多有關的知識請點擊  http://m.wurkt.com   真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://m.wurkt.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.