安裝卷簾門一定要知道的事有什么？濟南卷簾門主要由簾板、導軌及傳動裝置組成。濟南卷簾門在開啟時不占室內外面積，并且適合用于非頻繁開啟的高大洞口。卷簾門的寬度要和簾板的剛度相適應，其加工制作及安裝的要求也比較高。

What must we know when installing roller shutter doors? Jinan roller shutter door is mainly composed of shutter, guide rail and transmission device. Jinan roller shutter door does not occupy the indoor and outdoor area when it is opened, and it is suitable for tall openings that are not frequently opened. The width of the roller shutter door should adapt to the rigidity of the shutter, and its processing, manufacturing and installation requirements are also high.

簾板的形式主要有頁板式和空格式兩種，其中以頁板式用得比較多。頁板式簾板是用鍍鋅鋼板或鋁合金板軋制而成。頁板之間用鉚釘連接。

There are mainly two types of curtain boards, namely, leaf board and empty format, in which the leaf board is used more frequently. The sheet curtain is rolled from galvanized steel sheet or aluminum alloy sheet. The sheets are connected by rivets.

為了加強濟南卷簾門的剛度和便于安裝門鎖，在頁板的下部采用鋼板和角鋼，頁板的上部和卷筒連接。開啟時，頁板沿門洞兩側的導軌上升，卷在卷筒上。

In order to strengthen the rigidity of Jinan roller shutter door and facilitate the installation of door lock, steel plate and angle steel are used at the lower part of the leaf plate, and the upper part of the leaf plate is connected with the drum. When it is opened, the leaf plate rises along the guide rails on both sides of the door opening and is rolled on the drum.

卷簾門的傳動裝置安裝在門洞的上部，這種裝置分手動式、鏈條式、搖桿式及電動式4種。手動式濟南卷簾門的傳動裝置有卷筒、托架、彈簧軸承等。

The transmission device of the rolling shutter door is installed on the upper part of the door opening, which is divided into four types: movable, chain, rocker and electric. The driving device of the manual Jinan roller shutter door includes a drum, a bracket, a spring bearing, etc.

它利用彈簧軸承來平衡門扇自重，所以這種門不應該過大。底部加強板兩端裝插銷插入側導軌，使門固定。

It uses spring bearings to balance the deadweight of the door leaf, so the door should not be too large. Both ends of the bottom stiffening plate are inserted with pins into the side guide rail to fix the door.

鏈條式濟南卷簾門是利用鏈條及幾個不同直徑齒輪的傳動，減輕啟閉重量。

The chain type Jinan roller shutter door is driven by a chain and several gears with different diameters to reduce the opening and closing weight.

搖桿式卷簾門是利用搖桿及傘狀齒輪變換傳動方向，開關方便，常用于開關空格式卷簾門，比電動式經濟。

Rocker type roller shutter is used to change the transmission direction with rocker and umbrella gear. It is convenient to open and close. It is often used to open and close the empty type roller shutter, which is more economical than electric type roller shutter.

電動式卷簾門的電機多數裝于上部，明露或設于墻內，減速器可以和電機分設或者設計成一個整體部件。電動式卷簾門的傳動裝置有卷筒、托輪、電動機、減速器等，減速器應該設置手動裝置，以備停電時卷簾門的啟閉用。

The motor of the electric roller shutter door is mostly installed on the upper part, exposed or set in the wall, and the reducer can be separated from the motor or designed as an integral part. The driving device of electric roller shutter door includes drum, supporting wheel, motor, reducer, etc. The reducer shall be equipped with manual device for opening and closing of roller shutter door in case of power failure.

安裝卷簾門一定要知道的事相關信息就講解到這里了，您對此有什么想說的就來我們網站http://m.wurkt.com咨詢吧！

This is the end of what you must know to install the roller shutter door. If you have anything to say about it, please come to our website http://m.wurkt.com Consult!