電動車庫門需要電，哪里是安裝電源插座的佳位置是我們應該考慮的一個問題。電動車庫門安裝后，發現電源位置不對后再換，會造成不必要的浪費。那么濟南車庫門的電源放在哪個位置合適呢？

The electric garage door needs electricity. Where is the best place to install the power socket is a problem we should consider. After the electric garage door is installed, it will cause unnecessary waste if the power supply is replaced after the wrong position is found. So where is the power supply for Jinan garage door?

電動車庫門的電機插座一般在1.5m左右，電源安裝在哪里要看安裝什么樣的車庫門。翻板車庫門的電機在車庫中間的后面，電源在后面。按照門口的高度，應該和門口高度加一米差不多。比如門口高2.5m，電源可以安裝在后面3.5m的門口中間。如果要安裝卷簾門，電源插座應安裝在門洞兩側的上方位置，距離門洞一米左右。車庫門電機的功率一般在80W到500W之間，所以電源線按2.5的標準即可。

The motor socket of the electric garage door is generally about 1.5m. Where the power supply is installed depends on what kind of garage door is installed. The motor of the flap garage door is behind the middle of the garage, and the power supply is behind. According to the height of the door, it should be about the same as the height of the door plus one meter. For example, the door is 2.5m high, and the power supply can be installed in the middle of the door 3.5m behind. If the roller shutter door is to be installed, the power socket shall be installed at the upper position on both sides of the door opening, about one meter away from the door opening. The power of the garage door motor is generally between 80W and 500W, so the power cord can meet the standard of 2.5.

此外車庫門電機使進入和保護車庫變得輕松而便捷。但是，如果電源中斷，您可能想知道如何打開它呢？

In addition, the garage door motor makes it easy and convenient to enter and protect the garage. However, if the power is interrupted, you may wonder how to turn it on?

不用電源打開車庫門很容易。找到車庫門電機上的紅色應急繩，將其拉開。然后，您可以通過升起或降下手動打開和關閉門。當電源恢復供電時，請關閉門，拉動繩子以重新接合電機，然后將門滑到軌道上。

It's easy to open the garage door without power. Find the red emergency rope on the garage door motor and pull it apart. You can then manually open and close the door by raising or lowering it. When the power supply is restored, close the door, pull the rope to re engage the motor, and then slide the door onto the track.

1、拔下車庫門電機的電源。車庫門電機位于車庫天花板上的軌道的底部。從機器上拔下電源線，以便您可以將門與自動軌道分離。萬一電源重新打開，您不希望自動開啟器在門未接合時嘗試打開門，否則可能使您難以將門重新連接到軌道上。

1. Unplug the garage door motor. The garage door motor is located at the bottom of the track on the garage ceiling. Unplug the power cord from the machine so that you can separate the door from the automatic track. In case the power is turned on again, you do not want the automatic opener to try to open the door when the door is not engaged, otherwise it may make it difficult for you to reconnect the door to the track.

2、拉出緊急電源線，以將門與電機斷開連接。找到門上方軌道上一根繩子上懸掛的紅色把手。垂直向下拉動手柄，直到聽到“喀噠”聲為止。

2. Pull out the emergency power cord to disconnect the door from the motor. Find the red handle hanging from a rope on the track above the door. Pull the handle vertically downward until you hear "click".

3、抓住門的底部并將其筆直向上提起。您可以手動打開門。牢牢抓住門，然后將其筆直向上提起，使其沿著軌道行進。繼續抬起門直到它完全打開。

3. Grasp the bottom of the door and lift it straight up. You can open the door manually. Hold the door firmly and lift it straight up so that it travels along the track. Continue to lift the door until it is fully open.

將門一直滑到地板上以將其關閉。當您準備關上車庫門時，請輕輕將其降低與地面牢固連接。門的重量應使其保持關閉狀態。請勿猛烈撞擊或讓門自行跌落，否則可能會損壞軌道或門本身。更多相關事項就來我們網站http://m.wurkt.com咨詢吧！

Slide the door all the way to the floor to close it. When you are ready to close the garage door, gently lower it to firmly connect with the ground. The weight of the door shall keep it closed. Do not hit the door violently or let the door fall by itself, otherwise the track or the door itself may be damaged. For more information, please visit our website http://m.wurkt.com Consult!