車庫門之所以在當下被廣泛的應用，主要的原因在于車庫卷簾門順應人們的使用習慣，而且車庫卷簾門使用起來方便快捷，應用范圍廣，但是在操作濟南車庫門的時候，還是要注意一些事項的，下面咱們一起來了解一下車庫門的操作事項吧：

The main reason why garage doors are widely used at present is that garage rolling doors conform to people's usage habits, and garage rolling doors are convenient and fast to use, with a wide range of applications. However, when operating Jinan garage doors, we should pay attention to some matters. Let's learn about the operation of garage doors:

1、車庫門變頻器運轉中嚴禁將馬達機組投入或切離，否則會造成變頻器過電流跳脫，甚變頻器主回路燒毀。

1. During the operation of garage door inverter, it is strictly forbidden to put the motor unit into operation or cut it off, otherwise, the inverter will trip due to overcurrent, or even the main circuit of the inverter will be burnt.

2、變頻器送電過程中請勿取下前蓋，以防止感電受傷。

2. Do not remove the front cover during power transmission of the inverter to prevent electric injury.

3、在開啟故障再啟動功能時，馬達在運轉后會自動再啟動，請勿靠近機器，以免發生意外。

3. When the fault restart function is enabled, the motor will restart automatically after running. Please keep away from the machine to avoid accidents.

4、散熱座、剎車電阻等發熱元件請勿觸摸，以防燙傷。

4. Please do not touch the radiator, brake resistor and other heating elements to prevent scalding.

5、變頻器可以很容易從低速到高速運轉，請確認馬達與機器的速度容許范圍。

5. The frequency converter can easily run from low speed to high speed. Please confirm the allowable speed range of motor and machine.

6、快速車庫卷簾門變頻器運轉中請勿檢查電路板上的信號，以免發生危險。

6. Please do not check the signal on the circuit board during the operation of the speed garage shutter door converter to avoid danger.

7、變頻器出廠時均已調整設定，請不要任意加以調整，按所需功能適當調整。

7. The frequency converter has been adjusted when leaving the factory. Please do not adjust it arbitrarily, and adjust it appropriately according to the required functions.

8、變頻器超過50HZ以上頻率運行時，請務必考慮振動、噪音、電機軸承及機械裝置所允許的速度范圍。

8. When the frequency converter operates above 50HZ, please be sure to consider the allowable speed range of vibration, noise, motor bearings and mechanical devices.

9、采用機械行程定位時，遇停電可用手動搖桿將門打開。系統來電后，將電源開關接通后，門可正常使用。

9. When mechanical stroke positioning is adopted, the door can be opened by manual rocker in case of power failure. After the system is powered on, the door can be used normally after the power switch is turned on.

10、采用編碼器定位時，門體無手動升降過，來電接通后門可正常使用。手動調節門體，來電需要重新定位后方能使用。

10. When the encoder is used for positioning, there is no manual lifting of the door body, and the back door can be used normally when the power is connected. Manually adjust the door body. It can only be used after an incoming call is repositioned.

不知道大家在看完上文之后有沒有對此有更深入的了解了呢?在使用車庫卷簾門的時候，一定要按照操作嚴格執行，而且還要定期對車庫卷簾門進行護理，延長車庫卷簾門的使用壽命。關注我們http://m.wurkt.com了解更多！

Do you have a deeper understanding of this after reading the above? When using the garage roller shutter door, it must be strictly implemented according to the operation, and the garage roller shutter door must be regularly cared to extend the service life of the garage roller shutter door. Follow us http://m.wurkt.com Learn more!